Documents by Year
1980s (2)
1990s (87)
2000s (2207)
2010s (7288)
2020s (417)
Other (16)

ST RK

ST RK IEC/TU 62257-5-2011
ST RK IEC/TU 62257-5-2011
Electrification of the village. Renewable energy systems and low power hybrid systems. Part 5. Protection against electric shock. Date of introduction from 2012.07.01
ST RK IEC/TU 62257-6-2011
ST RK IEC/TU 62257-6-2011
Electrification of the village. Renewable energy systems and low power hybrid systems. Part 6. Acceptance, operation, maintenance and replacement. Date of introduction from 2012.07.01
ST RK IEC/TU 62257-7-3-2011
ST RK IEC/TU 62257-7-3-2011
Recommendations on small renewable energy systems and mixed systems for rural electrification. Part 7-3. Generator sets. Selection of generator sets for rural electrification systems. Date of introduction from 2013.01.01
ST RK ISO 10137-2011
ST RK ISO 10137-2011
Operating reliability of buildings and crossovers under the conditions of vibration. Principles of design of building structures
ST RK ISO 10405-2011
ST RK ISO 10405-2011
Oil and gas industry. Servicing and applying of casing pipes and oil-well tubing
ST RK ISO 10426-1-2011
ST RK ISO 10426-1-2011
Oil and gas industry. Cements and well cementing materials. Part 1. Specification
ST RK ISO 10426-3-2011
ST RK ISO 10426-3-2011
Oil and gas industry. Cements and well cementing materials. Part 1. Test of compounds based on cement for deep-water wells
ST RK ISO 10426-4-2011
ST RK ISO 10426-4-2011
Oil and gas industry. Cements and well cementing materials. Part 1. Preparation and testing of foaming cement slurries under atmospheric pressure
ST RK ISO 10426-5-2011
ST RK ISO 10426-5-2011
Oil and gas industry. Cements and well cementing materials. Part 1. Determination of shrinkage and expansion of cement-based compounds under atmospheric pressure
ST RK ISO 10426-6-2011
ST RK ISO 10426-6-2011
Oil and gas industry. Cements and well cementing materials. Part 1. Methods for determination of cement compounds gel strength
ST RK ISO 10427-2-2011
ST RK ISO 10427-2-2011
Oil and gas industry. Cementing equipment. Part 1. Positioning of the centralizer and stop collar test
ST RK ISO 10428-2011
ST RK ISO 10428-2011
Oil and gas industry. Pump rods (pony rods, esture rods, couplings and pipe bushings) - Specification
ST RK ISO 10432-2011
ST RK ISO 10432-2011
Oil and gas industry. Well equipment. Subsurface safety valves. In substitution of ST RK ISO 10432-2004
ST RK ISO 10474-2011
ST RK ISO 10474-2011
Steel and steel products. Control documents
ST RK ISO 10810-2011
ST RK ISO 10810-2011
Chemical surfaces analysis. X-ray photoelectron spectroscopy. Analysis guideline
ST RK ISO 11052-2011
ST RK ISO 11052-2011
Wheat flour for macaroni and whitlow grass. Determination of content of cassel yellow
ST RK ISO 11085-2011
ST RK ISO 11085-2011
Cereals, cereals products and animal feeding stuffs. Determination of crude fat and total fat content by the Randall extraction method
ST RK ISO 11124-1-2011
ST RK ISO 11124-1-2011
Treatment of steel faces before painting and related products. Performance specification for metal abrasives for blast cleaning -. Part 1. General principles and classification
ST RK ISO 11124-2-2011
ST RK ISO 11124-2-2011
Treatment of steel faces before painting and related products. Performance specification for metal abrasives for blast cleaning. Part 1. Grains of chilled cast iron
ST RK ISO 11124-3-2011
ST RK ISO 11124-3-2011
Treatment of steel faces before painting and related products. Performance specification for metal abrasives for blast cleaning. Part 3. Shot and grains of high-carbon cast steel
ST RK ISO 11124-4-2011
ST RK ISO 11124-4-2011
Treatment of steel faces before painting and related products. Performance specification for metal abrasives for blast cleaning. Part 4. Shot of low-carbon cast steel
ST RK ISO 11146-1-2011
ST RK ISO 11146-1-2011
Lasers and laser-related equipment. Test methods for laser beam widths, divergence angles and beam propagation ratios. Part 1. Stigmatic and simple astigmatic beams
ST RK ISO 11146-2-2011
ST RK ISO 11146-2-2011
Lasers and laser-related equipment. Test methods for laser beam widths, divergence angles and beam propagation ratios. Part 1. General astigmatic beams
ST RK ISO 11223-2011
ST RK ISO 11223-2011
Oil and liquid oil products. Direct static measurements. Changing of content of vertical storage tanks by means of hydrostatic tank measuring
ST RK ISO 11323-2011
ST RK ISO 11323-2011
Iron ores and direct-reduced iron. Glossary
ST RK ISO 1139-2011
ST RK ISO 1139-2011
Textile. Yarn designation
ST RK ISO 11702-2011
ST RK ISO 11702-2011
Animal and vegetable fats and oils. Sterols total content fermentive determination
ST RK ISO 11759-2011
ST RK ISO 11759-2011
Rubber hoses and assembly rubber hoses for pumping over of liquefied petroleum gases. Specification
ST RK ISO 12003-2-2011
ST RK ISO 12003-2-2011
Agricultural and forestry tractors. Roll-over protective structures on narrow-track wheeled tractors. Part 1. Protection devices at rear-mounted turnover
ST RK ISO 1211-2011
ST RK ISO 1211-2011
Milk. Determination of fat content. Gravimetrical method (control method)
ST RK ISO 12213-1-2011
ST RK ISO 12213-1-2011
Natural gas. Compression ratio calculation. Part 1. Introduction and guidelines. In substitution of ST RK ISO 12213-1-2004
ST RK ISO 12213-2-2011
ST RK ISO 12213-2-2011
Natural gas. Compression ratio calculation. Part 1. Calculation based on molar percentage analysis. In substitution of ST RK ISO 12213-2-2004
ST RK ISO 12213-3-2011
ST RK ISO 12213-3-2011
Natural gas. Compression ratio calculation. Part 1. Physical characteristics-based calculation. In substitution of ST RK ISO 12213-3-2004
ST RK ISO 12368-2011
ST RK ISO 12368-2011
Agricultural vehicles. Mechanical hooky connections on towing vehicles. Testing methods and specification
ST RK ISO 13041-1-2011
ST RK ISO 13041-1-2011
Numerically controlled multi-purpose turning lathes. Test conditions. Part 1. Test of geometrical parameters of vertical-type machines for work-holding of processed part
ST RK ISO 13041-2-2011
ST RK ISO 13041-2-2011
Numerically controlled multi-purpose turning lathes. Test conditions. Part 1. Test of geometrical parameters of vertical-type machines for work-holding of processed part
ST RK ISO 13041-3-2011
ST RK ISO 13041-3-2011
Numerically controlled multi-purpose turning lathes. Test conditions. Part 1. Test of geometrical parameters of reversed vertical-type machines for work-holding of processed part
ST RK ISO 13041-4-2011
ST RK ISO 13041-4-2011
Numerically controlled multi-purpose turning lathes. Test conditions. Part 1. Accuracy and repeat accuracy of linear and rotating axles
ST RK ISO 13041-5-2011
ST RK ISO 13041-5-2011
Numerically controlled multi-purpose turning lathes. Test conditions. Part 1. Accuracy of supplying, velocities and interpolations
ST RK ISO 13041-6-2011
ST RK ISO 13041-6-2011
Numerically controlled multi-purpose turning lathes. Test conditions. Part 1. Accuracy of machined sample-product
ST RK ISO 13041-7-2011
ST RK ISO 13041-7-2011
Numerically controlled multi-purpose turning lathes. Test conditions. Part 1. Evaluation of contour machining in the coordinate planes
ST RK ISO 13041-8-2011
ST RK ISO 13041-8-2011
Numerically controlled multi-purpose turning lathes. Test conditions. Part 1. Evaluation of thermal deformations
ST RK ISO 13370-2011
ST RK ISO 13370-2011
Buildings thermal parameters. Heat transfer through ground. Calculation methods
ST RK ISO 13501-2011
ST RK ISO 13501-2011
Oil and gas industry. Drilling Mud. Process equipment assessment
ST RK ISO 13678-2011
ST RK ISO 13678-2011
Oil and gas industry. Assessment and testing of thread compounds on casing pipes, pump-compressor pipes, pipelines and components of drill columns
ST RK ISO 13704-2011
ST RK ISO 13704-2011
Oil and gas industry. Calculation of thickness of heating units pipes for refineries
ST RK ISO 13757-2011
ST RK ISO 13757-2011
Liquefied oil gases. Determination of oil residuals. High-temperature method
ST RK ISO 13903-2011
ST RK ISO 13903-2011
Animal feeding stuffs. Determination of content of amino acids

All Codes and Regulations

MSP PST RK RK Codes RK Laws SN RK TR EAES
NTP RK PUE RK Decisions RK Letters SNiP RK
Other RK norms R RK RK Decrees RK Orders SP RK
PR RK RDS RK RK Instructions RK Resolutions ST RK

All Categories

Construction (Max) Highways (Max) National Standards for KGS (State Standards Classification) Projects of works (PPR) on bridges Technical Supervision
Construction Price Formation ISO classifier Organization Standards PromExpert Welding regulations
Evidence base (TR CU, Technical Regulation of the Customs Union) National standards Power industry Standards for pipe fittings (TPA)

Send us a message Expand Collapse

Leave your message in the form below, and we will write back by e-mail!